Difference between revisions of "T15 Olympus BH microscope"

From Chemical Engineering @ UP wiki
Jump to: navigation, search
Line 57: Line 57:
 
SL-BOCLE (ASTM D6078)
 
SL-BOCLE (ASTM D6078)
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/ASTM%20D6078%20SLBOCLE.PDF click here]
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/ASTM%20D6078%20SLBOCLE.PDF click here]
 
=== MSDS of relevant Chemicals ===
 
Acetone
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/MSDS%20Acetone.pdf click here]
 
<br/>
 
Isooctane
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/MSDS%20Isooctane.pdf click here]
 
<br/>
 
Isopropyl alcohol
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/MSDS%20Isopropyl%20alcohol.pdf click here]
 
<br/>
 
Reference fuels (A&B)
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/MSDS%20Ref%20fuels.doc click here]
 
  
 
=== Wiring, Flow & Instrumentation diagrams ===
 
=== Wiring, Flow & Instrumentation diagrams ===
Line 79: Line 66:
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/SLBOCLE%20overall2012.pdf PDF]
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/SLBOCLE%20overall2012.pdf PDF]
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/SLBOCLE%20overall22012.vsd VISIO]
 
[ftp://ragnarok.up.ac.za/publicftp/lab/Tribology/New%20Folder/SLBOCLE%20overall22012.vsd VISIO]
 
  
  

Revision as of 14:31, 28 June 2013

Olympus BH Microscope

Used to:

  1. Measure wear scar and/or wear track size
  2. Capture wear scar and/or wear track appearance.


Typically used with:

  1. BOCLE
  2. SL-BOCLE
  3. HFRR
  4. SRV
BOCLE(Left) & SL-BOCLE(Right)

Both the Ball On Cylinder Lybricity Evaluator (BOCLE) and the Scuffing Load - Ball On Cylinder Lubricity Evaluator work on the principle of testing the lubricity of a fuel/lubricant. A non-rotating ball is forced against a rotating cylinder. The cylinder is partially immersed in a bath of the fuel to allow the fuel to be constantly carried to the area of contact.

The BOCLE & SL-BOCLE machines operate on much the same principals. They are nearly identically constructed. They differ in:
1) The types of fuels they typically test.
2) The qualifying parameters and test methods (See ASTM link below).
3) The maximum load they can carry.

The BOCLE is a wear test. A microscope and camera is used to quatify the size and record the appearance.

The SL-BOCLE is a load carrying capacity test. A series of loads are applied until a sudden change in the friction coefficient is observed (higher than 0.175). This load then represents some of the lubricity behaviour.
Note the suggested loading sequence in the operating manual.

Ball,Ring & Bath


In this Table some basic differences are presented:


BOCLE table 2.jpg

Both units are operated via a simulink interfaces found on the PC next to the units (Univ PC nr: 766118).



Documentation

User Manual

A single user manual exists for both machines. click here

ASTM Standards

BOCLE (ASTM D5001) click here
SL-BOCLE (ASTM D6078) click here

Wiring, Flow & Instrumentation diagrams

Overall wiring diagram
BOCLE
PDF VISIO
SL-BOCLE
PDF VISIO


Detailed Opto wiring diagram
BOCLE
PDF VISIO
SL-BOCLE
PDF VISIO


Piping diagram (Air flow) Identical for both click here

History of this Equipment

The equipment was recieved from Sasol in 2012 after being used there for a period of time. The equipment was conntected to the OPTO 22 network in 2012 by Jacques Langenhoven to allow data logging and control through the lab network and OPTO system.

Current/Previous projects

2012

Jacques Langenhoven, The commissioning of the BOCLE & SL-BOCLE in the Tribology lab
PDF
MS WORD