Difference between revisions of "Calculating Marks"

Revision as of 07:38, 25 June 2015 (view source) Alchemyst (Talk | contribs) (Borderline cases) ← Older edit		Revision as of 07:41, 25 June 2015 (view source) Alchemyst (Talk | contribs) m (Update yearbook year) Newer edit →
Line 31:		Line 31:
	<pre>		<pre>
	function engineeringstatus(semester as integer, exam as integer, final as integer) as string		function engineeringstatus(semester as integer, exam as integer, final as integer) as string
−	' Criteria for assessing supplementary exams, according to engineering yearbook 2010	+	' Criteria for assessing supplementary exams, according to engineering yearbook 2015
	' Author: Carl Sandrock		' Author: Carl Sandrock
	if final < 40 then		if final < 40 then

---

Revision as of 07:41, 25 June 2015

Calculating marks

Remember that you need to follow the Undergraduate external process while doing the marks.

Rounding

Make sure that you round the semester mark, the exam mark and the final mark and rework with integer percentages (avoid the use of the Excel Percentage type, as this hides some common errors). Use

round(mark/total*100, 0)

Borderline Cases

(From the 2015 yearbook, p14 point Eng 3 (c) (i))

Borderline cases (e.g. a mark of 49% or 74%) must be reconsidered by both the internal and external examiners, for determination of the possible merit of an upward adjustment of the mark. Marks may not be adjusted downwards, except when obvious marking and adding errors were detected.

Supplementary exams

Always check the relevant yearbook. The following description is from the 2015 Yearbook.

In the School of Engineering a supplementary examination is only granted in instances where:

1. A final mark of between 45% and 49% was achieved;
2. A final mark of between 40% and 44% was achieved and where the candidate also achieved either a semester mark or an examination mark of 50% or higher;
3. A pass mark has been obtained, but the required subminimum in the examination section of the module or divisions thereof has not been obtained.
4. A final mark of between 40% and 49% has been obtained in first-year modules in the first semester.

In most cases the third point above translates to simple rule that a supp must be awarded if the final mark is a pass mark but the exam mark is less than 40.

This is summarised in the following picture (assuming the exam and semester marks count 50% each toward the final mark):

The following VBA function can be used to do the calculation in Excel:

function engineeringstatus(semester as integer, exam as integer, final as integer) as string
' Criteria for assessing supplementary exams, according to engineering yearbook 2015
' Author: Carl Sandrock
	if final < 40 then
		engineeringstatus = "Fail"
	elseif final < 45 then
		if semester >= 50 or exam >= 50 then
			engineeringstatus = "Supp"
		else
			engineeringstatus = "Fail"
		end if
	elseif final < 50 or exam < 40 then
		engineeringstatus = "Supp"
	else
		engineeringstatus = "Pass"
	end if
end function

This is equivalent to the following formula (fill in the correct cells in semester, exam and final)

=if(final<40, "Fail", if(final<45, if(or(semester>=50, exam>=50), "Supp", "Fail"), if(or(final<50, exam<40), "Supp", "Pass")))

Calculation of the final supplementary examination mark

1. The semester mark is retained and the final mark is calculated as the weighted average of the supplementary examination mark and the semester mark, in accordance with the formula as published in the study manual of the specific module, with the proviso that the maximum final mark awarded may be no more than 50%. The only exception to this rule is in the case of first-year modules on first-semester level, where the semester mark is not considered, and where the supplementary examination mark is taken as the final mark, with the proviso that the maximum final mark awarded may be no more than 50%.
2. All other pass requirements, as published in the study manual of each specific module, remain so and are applicable during the determination of the final result of a supplementary examination in the module.

Codes

Several codes are used to communicate special status in the CSV file that Admin expects to get from you after you have calculated the marks.

	Semester	Examination	Final	Remark
Examination refusal	Mark	988	988
Unknown	987	987	987
Absent from exam	Mark	987	987
Mark not avalable - Finance	Mark	xxx	xxx
Mark not avalable - Library	Mark	yyy	yyy
Mark not avalable - Both	Mark	zzz	zzz
Aegrotat exam	Mark	987	987	994
Supplementary	Mark	Mark	Mark	999
Subminimum	Mark	Mark	992(only if above 50%)	999
Promote(only School of IT)	Mark	973	973
Only postgraduate:
Mark not yet available	989	989	989
Did not complete	995	995	995