Difference between revisions of "FZG spares"
From Chemical Engineering @ UP wiki
| (8 intermediate revisions by the same user not shown) | |||
| Line 1: | Line 1: | ||
| + | The captions to each of the following spare parts refer to the position number of the part on the FZG technical drawings. | ||
| + | |||
<gallery> | <gallery> | ||
| − | File:Angle_Head_Screws_x6_-Position_104-.JPG | + | File:Angle_Head_Screws_x6_-Position_104-.JPG|Position 104 |
| − | File:Bearing_Cover_x1_-Position_6-.JPG | + | File:Bearing_Cover_x1_-Position_6-.JPG|Position 6 |
| − | File:Bolt_For_Gear_Boxes_x10_-Position_74-.JPG | + | File:Bolt_For_Gear_Boxes_x10_-Position_74-.JPG|Position 74 |
| − | File:Bolt_For_Holding_Down_Gear_Boxes_With_Washers_x2_-Position_27_%26_28-.JPG | + | File:Bolt_For_Holding_Down_Gear_Boxes_With_Washers_x2_-Position_27_%26_28-.JPG|Position 27 |
| − | File:Centring_Pins_x2_-Position_66-.JPG | + | File:Centring_Pins_x2_-Position_66-.JPG|Position 66 |
| − | File:Holding_Pins_x2_-Position_34-.JPG | + | File:Holding_Pins_x2_-Position_34-.JPG|Position 34 |
| − | File:Key_%28A_8x5x50%29_x3_-Position_20-.JPG | + | File:Key_%28A_8x5x50%29_x3_-Position_20-.JPG|Position 20 |
File:Key_For_Torsion_Shaft_x4.JPG | File:Key_For_Torsion_Shaft_x4.JPG | ||
| − | File:Load_Clutch_Bolt_x4_-Position_63-.JPG | + | File:Load_Clutch_Bolt_x4_-Position_63-.JPG|Position 63 |
| − | File:Load_Coupling_Flanges_x1_-Position_61_%26_62-.JPG | + | File:Load_Coupling_Flanges_x1_-Position_61_%26_62-.JPG|Position 61/62 |
| − | File:Locking_Nut_%28MB5%29_x2_-Position_10-.JPG | + | File:Locking_Nut_%28MB5%29_x2_-Position_10-.JPG|Position 10 |
| − | File:Nut_%28M25x1%29_x2_-Position_11-.JPG | + | File:Nut_%28M25x1%29_x2_-Position_11-.JPG|Position 11 |
| + | File:Roller_Bearing_Inner_Half_x8_-Position_8-.JPG|Position 8 | ||
| + | File:Screw_For_Bearing_Covers_x11_-Position_29-.JPG|Position 29 | ||
| + | File:Slave_Gear_Shaft_x1_-Position_43-.JPG|Position 43 | ||
| + | File:Slave_Gear_Shaft_x1_-Position_46-.JPG|Position 46 | ||
| + | File:Test_Gear_Shaft_%28With_Broken_Centering_Pin%29_x1_-Position_42-.JPG|Position 42 | ||
| + | File:Test_Gear_Shaft_x1_-Position_44-.JPG|Position 44 | ||
| + | File:Torsion_Shaft_-_13_Diameter_x1_-Position_645-.JPG|Position 645 | ||
| + | File:Torsion_Shaft_-_23_Diameter_x1_-Position_45-.JPG|Position 45 | ||
</gallery> | </gallery> | ||
Latest revision as of 11:35, 2 August 2010
The captions to each of the following spare parts refer to the position number of the part on the FZG technical drawings.
Position 104
Position 6
Position 74
Position 27
Position 66
Position 34
Position 20
Position 63
Position 61/62
Position 10
Position 11
Position 8
Position 29
Position 43
Position 46
Position 42
Position 44
Position 645
Position 45
_x3_-Position_20-.JPG)
_x2_-Position_10-.JPG)
_x2_-Position_11-.JPG)
_x1_-Position_42-.JPG)
